Danfoss FC 100 Series Instructions d'exploitation télécharger pdf (Page 65)

Store all set-ups:

All parameter values will be stored in the non-

volatile memory. The value returns to

Off

when all parameter

values have been stored.

10-33 Store Always

Option: Function:

[0]

Off

[1] On This parameter is used to select whether parameter data re-

ceived via the DeviceNet option should always be stored in non-

volatile memory.

16-90 Alarm Word

Range: Function:

[0 - FFFFFFFF] View the alarm word sent via the serial communication port in

hex code.

16-92 Warning Word

Range: Function:

[0 - FFFFFFFF] View the warning word sent via the serial communication port

in hex code.

FC 100/ 200/ 300 DeviceNet 6. Parameters

MG.33.D3.02 - VLT

is a registered Danfoss trademark

1 2 ... 60 61 62 63 64 65 66 67 68 69 70 ... 81 82

MG.33.D3.02 - VLT 1
Contents 2
Contents 3
1. Introduction 5
1.2.1. Safety Note 6
1.2.2. Safety Regulations 6
1.2.4. Warning 6
1.3. About this Manual 8
1.4. Technical Overview 8
1.5. Assumptions 9
1.6. Hardware 9
1.7. Background Knowledge 9
1.8. Available Literature 10
1.9. Abbreviations 11
MG.33.D3.02 - VLT 12
2. How to Install 13
2.1.3. EMC Precautions 14
2.1.5. ODVA Recommendation 15
2.1.6. Earth Connection 15
2.1.8. DeviceNet Termination 16
2.1.9. Drop Cable 16
2.1.7. DeviceNet Connection 16
Option Change 17
0x03, Attribute 1, Instance 1 19
Baudrate se 20
3.2. Configure the Master 21
4.1.1. Polling 23
4.1.2. Change of State, COS 23
4.2. I/O Assembly Instances 25
4.3. Process Data 25
4.4. ODVA Control Profile 27
20/70 and 21/71 30
Control Word Profile 32
Preset Reference 32
Preset Reference Select 32
Function Relay 34
Active Set-up 34
Set-up Select 34
Reference site 36
Motor Speed Low Limit 36
Motor Speed High Limit 36
Torque Limit Motor Mode 36
Torque Limit Generator Mode 36
101/151 37
5.1. Explicit Messages 39
5.2. Object Classes 39
5.3.2. Class ID 0x01 40
5.3.4. Class ID 0x03 40
5.3.6. Class ID 0x04 41
5.3.16. Class ID 0x29 48
5.3.18. Class ID 0x2A 49
5.4. Danfoss Object Classes 50
5.5.1. Example 51
6. Parameters 53
FC profile 59
'*Off: 64
Store edit set-up: 64
Store all set-ups: 65
6.2. Parameter List 66
6.3. Data Types Supported 67
7. Application Examples 69
8. Troubleshooting 73
Coasting Select 76
Quick Stop Se 76
DC Brake Select 76
Digital input 76
Digital input [0] 77
Logic AND [2] 77
Logic OR [3] 77
Logic AND 78
Logic OR 78
8.2. Alarm/Warning Limits 80

Commentaires sur ces manuels

Pas de commentaire

Danfoss FC 100 Series Instructions d'exploitation Page 65

Commentaires sur ces manuels

Produits connexes et manuels pour Mise en réseau Danfoss FC 100 Series